Ultra-Micro Mechanical Steam Jet Mill Micronizer is a crushed device commonly used in industrial production. Due to its excellent performance, it is widely used in the pulverization operation of various materials. Although this work is very prominent, we still have to look at the machine, just like a normal machine, check the machine, eliminate the machine failure, make the machine more efficient and safely.
What is the design structure of Ultra-Micro Mechanical Steam Jet Mill Micronizer?
Under the action of the high-speed rotary impeller, the gas pressure flowing through the impeller increases, and the high pressure gas stream flows from the leaf, the fine particles are ejected. Since the blade of the rotary guiding blade is designed as a bend, the inlet cross-section is large, the exit cross-sectional area is small, so the airflow pressure at the outlet is reduced, the speed is increased, and the rotational flow is conducive to classification.
The hierarchical point adjustment mechanism sets three adjustment rods and keeps its synchronous motion using the chain. When the adjustment rod moves up, the fine powder is increased; when the adjustment rod moves down, the fine powder is reduced. The graded point can be continuously adjusted, the performance of the Ultra-Micro Mechanical Steam Jet Mill Micronizer is steplessly adjusted, the granular weight product can reach D97 ≤ 3 ≤ 150 microns, suitable for fine grading of dry micrometer products.
The setting of the control ring is to ensure a suitable cross section between the control ring and the jet fine particles, control the stability of the airflow flow. The residual windlet inevitably introduces excess gas from the dry material, the temperature of the classification chamber is high, and the air can expand, so a residual tight is designed to maintain the stability and balance of the graded indoor airflow.
Main performance characteristics of airflow pulverizer: 1, it includes vertical classification equipment, product size D97: 8 150 microns adjustable, granular shaped distribution narrow. It can be used in series with multi-stage classifiers, or producing multiple granular products at a time. 2, the device is disassemble and cleaning, the inner wall is smooth, no dead angle. The entire system is closed, less dust, low noise, clean and hygienic production process. 3. The control system uses program control and easy to operate.
Let's talk about how to correctly use the Ultra-Micro Mechanical Steam Jet Mill Micronizer
1. Prepare before booting the host, attachment machine, pipeline, and valve, whether it is intact, can you normal work.
Second, open
1. Turn on the compressor power supply, the pressure valve and the main air valve of the dust collector, then turn on the power switch of the powder machine, and turn on the power.
2. From the zero start grading wheel and gradually adjust to the specified speed.
3. Switching the fan, the cyclone separator discharges, dust removal, the power supply, and then turn on the total power supply of the barrel, set the inverter frequency, and then begins to break.
4. The particle size of the finished wheel can be adjusted by grading wheel frequencies and charging.
Third, the order of shutdown is: inverter - feeder - Main valve - Compressor - Steppered wheel Motor - Cyclone discharge, dust removal switch - Fan - Total Power - Air Compressor.
Fourth, repair
1. The motor should be lubed regularly, but the grease should not be too large, the bearing temperature is too high.
2. Hierarchical impeller, screw feeder, crushing nozzle wear should pay attention to check, belt tight and suitable.
3. After a crushing material, after a certain period of time, it is necessary to remove the viscosity of the chalk to avoid clogging, thereby affecting the crushing effect.
4. After the filter bag, you should clean or replace it.
V. Note
1. When the discharge device is running, the unloading port cannot be extended to avoid accidents.
2. The rotational speed of the impeller must not exceed the specified requirements, otherwise the temperature is too high, the impeller, and the electric machine are damaged.
3. Regularly check the safety valve to ensure safety.
El Pist Activated Carbon Ultra-Micro Mechanical Steam Jet Mill Micronizer Case Sharing: This customer is a research institute Dalian, which requires ultrafine pulverizing activated carbon during research. Investigate a number of domestic manufacturers, and finally choose to cooperate with our Else, purchased a Ultra-Micro Mechanical Steam Jet Mill Micronizer.
Shandong El Pie Wait-supplied Earn Ultra-Micro Mechanical Steam Jet Mill Micro Mechanical Steam Jet Mill Micro MICHANICAL Steam Jet Mill Micronizer. If you need to purchase Ultra-Micro Mechanical Steam Jet Mill Micronizer, please feel free to contact us.
