We all know that Ultra Fine Steam Jet Mill Grinding is a very strong airflow crushing equipment. Many stubborn hard materials will be cut into a uniform block of pulverization,
In terms of air flow grinding, you must first understand that its operating rules are very important, because only familiarize yourself with the operation procedure, you can do it correctly.
First, the operation rules for Ultra Fine Steam Jet Mill Grinding are as follows: Prepare materials before the start of the production order, prepare materials. Complete the site to clean the grocery. Check whether the transportation pipes and auxiliary equipment, whether the pipelines are blocked, leak or poor sealing, whether the auxiliary equipment is intact, whether it can work properly. Whether there is a phenomenon that the material is stacked in the outer casing and the separator, if the accumulated material is required. Whether the bearing is lubricated, whether it is lubricated in an appropriate place. Check if all pipes, fastening bolts, washers, spindles, and instruments are intact, normal and flexible.
Second, Ultra Fine Steam Jet Mill Grinding starts the motor, control the current and time at starting, so that the device can start running. When the equipment is operating normally, the feed speed can be adjusted according to the properties of the material. Uniform continuous feed should be achieved, not large or small, thereby affecting the separation effect of the grinding machine, making the machine easily fail. During operation, if an abnormality occurs, stop checking immediately before the failure continues.
Third, the main procedures of the close and inspection of Ultra Fine Steam Jet Mill Grinding are as follows: After the material in the grinding machine housing is completely pulverized, it should stop the feed and turn off the motor. After the machine is idling for 3 minutes, press the stop button to stop the machine. When the machine is completely stopped, open the check door and check the wear of the vulnerable part. Fill in the corresponding production record, update the device status flag, which is convenient for the next time.
The working principle of Ultra Fine Steam Jet Mill Grinding is a complete crushing system composed of crushers and cyclone separators, dust collectors and air blowers. After the compressed air is filtered, the high-speed nozzle is sprayed into the crushing chamber, and the material is pulverized by repeated collision, friction and shearing at the intersection of the multi-high pressure airflow. The crushing material moves together with the rising airflow to the grading area with the suction of the fan. Under the action of centrifugation, the thickness of the material is separated, and the grading cyclone is required to grade the cyclone to enter the cyclone dust collector, and the coarse comminution continues to be pulverized down. Suitable for dry crushing of various materials that are less than 9 in the Moh-hardness, especially for high hardness, high purity, high value-added crushing materials. It includes a vertical classification device. The size of the product can be adjusted between D97: 8 and 150 microns, with a good particle shape and a narrow particle size distribution. Low temperature without media crushing. It is especially suitable for thermal sensitivity, low melting point, sugar-containing and volatile substances. The grinding process mainly depends on the collision of the material itself, which is different from the impact of the mechanical crushing blade or the hammer on the ground on the ground, so the equipment has high wear resistance and high product purity.
Ultra Fine Steam Jet Mill Grinding is widely used, do you know how to use it correctly? The following content hopes to help you.
2, open the machine
(1) Turn on the compressor power supply, the dust collector pressure valve and the main air valve, open the air pulverizer power switch, and turn on the power switch.
(2) From scratch, adjust to the specified speed.
(3) Open the fan, cyclone separator, dust collector, charge motor, open the total power box, set the inverter frequency, and then start charging.
(4) The particle size of the finished product can be adjusted according to the frequency and bearing capacity of the grading wheel.
3, the sequence of stops is:
inverter-feeder-main air valve-compressor-grade impeller-motor cyclone material, dust removal switch-fan-main power supply-air compressor .
4, Maintenance
(1) The motor should be lubricated regularly, but the lubricating oil should not excessively avoid the bearing temperature too high.
(2) Checking the wear of impeller, helical conveyors and crushing nozzles.
(3) After pulverizing the material, the rubber powder should be removed to avoid clogging, thereby affecting the crushing effect.
(4) After a filter bag, you should clean or replace it.
5, Precautions
(1) When the discharge equipment is running, the unloading port cannot be reached, and the accident occurs.
(2) The impeller speed must not exceed the specified requirements, otherwise the temperature is too high, the impeller, and the electric chance are damaged.
(3) Regularly check the safety valve to ensure safety.
El Pie STEAM JET MITRA FINE Steam Jet Mill Grinding Experiment: A environmental protection technology company requires grading of aluminum superficition of aluminum silicate due to production demand, because uncertain demand can not be achieved, so feed Experiments, by experimenting our El Pie's air grade machine equipment can be graded, and finally the product particle size obtained by the experiment: D90: 18.3 μm, yield: 460kg / h 加量 加.. 123] Welcomes the major powdery grading needs manufacturers, to the factory to visit, incompetent experiments.
The equipment market is a rapidly changing. At present, the airflow classifier has certain demand in the market, but the society is constantly evolving, no matter what industry needs to keep paying with the times, it can lead the industry.
