Steam Jet Mill Machine of Ammonium Bicbonate is one of the common ultra-fine pulverations, widely used in non-metallic mines, drugs, chemicals, metallurgical and other industry materials, ultrafine pulverization or fine pulverization, with product particle size, particle size distribution Narrow, smooth surface surface, particle rules, high purity, high activity.
In terms of airflow milling, it is important to understand its operational rules, which is very important because only familiarize the procedure, can operate correctly.
1. The operating rules for Steam Jet Mill Machine of Ammonium Bicbonate are as follows: Prepare materials before the start of the production order, preparation materials. Complete the site to clean the grocery. Check whether the transportation pipes and auxiliary equipment, whether the pipelines are blocked, leak or poor sealing, whether the auxiliary equipment is intact, whether it works normally. Whether there is a phenomenon that the material is accumulated in the outer casing and the separator, if the accumulated material is required. Whether the bearing is lubricated, whether it is lubricated in an appropriate place. Check if all pipes, fastening bolts, washers, spindles, and instruments are intact, normal and flexible.
Second, Steam Jet Mill Machine Of Amomonium Bicbonate starts the motor, control the current and time at starting, so that the device can start. When the equipment is operating normally, the feed speed can be adjusted according to the properties of the material. Uniform continuous feed should not be large or small, thereby affecting the separation effect of the grinding machine, making the machine easily malfunction. During operation, if an abnormality occurs, stop checking immediately before the failure continues.
Third, Steam Jet Mill Machine of Ammonium Bicbonate The main procedures are as follows: After the material in the grinding machine housing is completely pulverized, it should stop the feed and turn off the motor. After the machine is idling for 3 minutes, press the stop button to stop the machine. When the machine is completely stopped, open the check door and check the wear of the vessel. Fill in the corresponding production record, update the device status flag, which is convenient for the next use.
The working principle of Steam Jet Mill Machine of Ammonium Bicarbonate is: the compressed air is dry, dry, and then enter the pulverizing cavity through the nozzle. In the pulverizing cavity, the material can be pulverized by a high pressure gas stream. Thereafter, the crude material can be separated from the centrifugal force generated by the grading turbine. Particles that meet the particle size requirements are in the cyclone separator and the dust collector, and the particles collected, and the particles that do not meet the requirements continue to be pulverized.
TEAM JET MILL MACHINE OF AMMONIUM BICARBONATE Switch In time to clean up
Daily maintenance Steam Jet Mill Machine Of Ammonium Bicarbonate To check the power outlet, plug, the power cord is no oxygen offset, the break, if you do not have a power test machine, when the motor is not rotated, When the hand is slightly turned to rotate, it can be concluded that one capacity fails in the two boot capacitors of the machine. If you can make a discharge spark and a very frightening, the capacitor can be used; if the sparks and sound are weak, the capacity of the capacitance has decreased, and the new or add a small capacitor. The airflow pulverizer does not use this method if the capacitor has damaged the short circuit, and it must be replaced with the same size new product.
In addition to Steam Jet Mill Machine of Ammonium Bicbonate, there is also a rod mill high-speed pulverizer. This crushing machine is very good, it is very difficult to damage, and daily maintenance is more important. This type of airflow pulverizer maintenance focus. Check if the lubrication of the bearing is good to check if all fasteners are tight. Check if the drive belt is installed correctly and the situation is good. Check if the protective device is good. If the protective device is found, it should be excluded in time. Check that there is no material or other debris in the damage chamber, if it is sometimes cleaned. Check if the hydraulic starting machine head or the starting roof rod is returned, the adjustment space is installed correctly and compact.
The above is the knowledge of the daily maintenance and maintenance of the STEAM JET MILL MACHINE OF AMMONIUM BICARBONATE manufacturers.
ALPA Chemical Raw Powder Steam Jet Mill Machine of Ammonium Bicbonate Case Sharing:
A mechanical company is a research and development of a complete set of equipment such as solder wire equipment, tin powder equipment, solder paste equipment, pure zinc equipment, Manufactured high-tech enterprises.
has a complete, scientific quality managementDepartment and powerful R \u0026 D teams, and continuous improvement of product performance.
The company is also a large-scale professional equipment manufacturing enterprise in China.
Case parameters:
hour yield: Sylect efficiency 60-90%
Shan dong alpa as a 20-year powder engineering equipment manufacturerThere are more than 3,000 customers at home and abroad, rich research and development experience has always led the front end of the industry, so before consulting, you need to provide the characteristics of the crushing material, the granularity parameters, production and production production range, purity requirements, specific process requirements (Anti-high temperature, explosion-proof, anti-dust pollution, etc.), professional engineers provide appropriate equipment models or system solutions according to this information.Welcome to inquire.
