With the development of society, the application of Laboratory Steam Jet Mill Machine has become more large.
Laboratory Steam Jet Mill Machine Ultrafine Crushed Union, Materials After the material is extracted, the powder properties will have a large change, and it is manifested as high viscosity after being affected. Powder is extremely prone to aggregation in the feed opening, pulverizing cavity and exhaust pipe, requires special treatment processes and specific design. Shandong Er Pieces Technology Co., Ltd. Design and developed materials and disseminated in the crushing of materials.
Laboratory Steam Jet Mill Machine Compressed Gases The high-speed jets generated by the feed nozzle The material particles in the bucket are introduced into the disc shocking chamber 3, and several jet nozzles are provided around the crushing chamber. The high-speed fluid is sprayed in the direction, producing an ultra-high speed swirl in the crushing chamber. The coarse particles in the opposite ultra-high-speed swirls in the ultra-high-speed swirls produced impact and friction in the intersection, and the particles were quickly pulverized. When the particles are pulverized below the fractional particle size below the fractional particle size, the centrifugal force of the particle movement is reduced, and the grading swirling is separated from the center outlet under action, and is collected from the center outlet. Such a pulverizer, the motion of the particles can be decomposed into two components in two directions in the intersection. In one direction, the direction of movement of the particles is substantially consistent, and there is no significant impact pulverization effect, and only in the other direction, the particles are opposite, and the particles produce effective impact. Therefore, this impact of this intersection is limited, and the energy of ultra-high-speed moving particles is not fully utilized, so the production energy consumption is still high.
Let's talk about how to use Laboratory Steam Jet Mill Mail Machine
1. Prepare before booting the host, attachment machine, pipeline, and valve, whether it is intact, whether it works fine.
Second, open
1. Turn on the compressor power supply, the pressure valve and the main air valve of the dust collector, then turn on the power switch of the powder machine, and turn on the power.
2. From the zero start grading wheel and gradually adjust to the specified speed.
3. Switching the fan, the cyclone separator discharges, dust removal, the power supply, and then turn on the total power supply of the barrel, set the inverter frequency, and then begins to break.
4. The particle size of the finished wheel can be adjusted by grading wheel frequencies and charging.
Third, the order of shutdown is: inverter - feeder - Main valve - Compressor - Steppered wheel Motor - Cyclone discharge, dust removal switch - Fan - Total Power - Air Compressor.
Fourth, repair
1. The motor should be lubed regularly, but the grease should not be too large, the bearing temperature is too high.
2. Hierarchical impeller, screw feeder, crushing nozzle wear should pay attention to check, belt tight and suitable.
3. After a crushing material, after a certain period of time, it is necessary to remove the viscosity of the chalk to avoid clogging, thereby affecting the crushing effect.
4. After the filter bag, you should clean or replace it.
V. Note
1. When the discharge device is running, the unloading port cannot be extended to avoid accidents.
2. The rotational speed of the impeller must not exceed the specified requirements, otherwise the temperature is too high, the impeller, and the electric machine are damaged.
3. Regularly check the safety valve to ensure safety.
El Pig Pigment Laboratory Steam Jet Mill Machine Case Sharing: This customer needs to use the pigment ultrafine pulverized equipment during its production. Through the ultrafine pulverization of the pigment, the quality of the product is to improve the product, after more than the same type of equipment, finally selected the Laboratory Steam Jet Mill Mill Mail Machine of our El. Compared with the same type of equipment, our company's product reliability is higher, the pulverized particle size is more uniform, and the particle size after pulverization is narrow, and there is no too much particle size range.
Technical parameters:
finished particle size: D90: 13μm;
Production capacity: 130kg / h
For more information, please pay attention to Shandong El Pieces Technology Co., Ltd., this The company mainly has airflow pulverizer, airflow mill, pharmaceutical gas flow crusher, disc air pulverizer, eddy current pulverizer.
